Smart Home Battery
Main feature of smart home battery:
- Application areas: Smart Home Monitor, Robot, Cordless phones and Security Alarm System etc.
- Li-ion polymer cells, Li-ion cylindrical cells and import branded cells solutions
- Standard type, High temperature type, Low temperature type and High Rate Type
- Chemistry systems: LiCoO2, Li(NiCoMn)O2, LiFePO4
- Single-cell and Multi-cells battery pack in series and parallel
- High performance, long service life and high safety characteristics
- Integrated intelligent PCBA
- Customized plastic case configuration
- KAYO branded promotion and OEM service
- Environmental friendly
Security Monitor Battery, SH-2, Cell Model: KPL523450-1000
This product complies with National Standard GB31241-2014《Lithium ion cells and batteries used in portable electronic equipments-Safety requirements
This specification is applied to KPL523450-1000mAh-3.7V battery Manufactured by SHENZHEN KAYO BATTERY Co., Ltd.
Product Configurations
No.
序号 |
Item
项目 |
Components Descriptions
零件描述 |
Remark
备注 |
1 | Li-ion Cell
锂离子电池 |
KPL523450 1000mAh 3.7V | KAYO |
2 | PCM / 保护板 | DW01+8205+10KNTC±1% B=3435 | TBD |
3 | Wire & Connector
导线与插头 |
Molex51021-3P 正向:红=黄=黑=UL1571#28AWG | 外露线长50±3mm |
Product Specifications
No.
序号 |
Item
测试项目 |
Performance
性能参数 |
Remark
备注 |
|
1 | Capacity
容量 |
Typical / 典型 | 1000mAh | Discharge at 0.2C to
3.00V after standard charge. 标准充电后,使用0.2C的电流放电到3.00V。 |
Minimum / 最小值 | 950mAh | |||
2 | Nominal Voltage
标称电压 |
3.7V | Operation voltage during
standard discharge. 标准放电过程的工作电压值 |
|
3 | Cut-off Voltage
放电终止电压 |
3.00V | Cut-off Voltage
放电终止电压 |
|
4 | Charging Voltage
充电电压 |
4.20V | ||
5 | Internal Impedance
内阻 |
≤180mΩ | AC 1KHz after standard charge
标准充电后AC 1KHz测试 |
|
6 | Standard Charge
标准充电 |
CC / CV: 4.20V / 0.2C charging till to the current decline to 0.02C, at 23℃.
恒流 / 恒压: 4.20V / 0.2C充电直到电流下降到0.02C,环境温度23℃ |
Charge time: Approx 6.0h.
充电时间:大约6小时 |
|
7 | Standard Discharge
标准放电 |
Discharge continuously with 0.2C to 3.00V.
使用恒流0.2C的电流连续放电到 3.00V。 |
||
8 | Fast Charge
快速充电 |
CC / CV: 4.20V / 0.5C charging till to the current decline to 0.02C, at 23℃.
恒流 / 恒压: 4.20V / 0.5C充电直到电流下降到0.02C,环境温度23℃ |
Charge time: Approx 3.0h.
充电时间:大约3小时 |
|
9 | Fast Discharge
快速放电 |
Discharge continuously with 0.5C to 3.00V.
使用恒流0.5C的电流连续放电到 3.00V。 |
||
10 | Max. Charge Current
最大充电电流 |
0.5C | ||
11 | Max. Continuous
Discharge Current 最大连续放电电流 |
0.5C | ||
12 | Operation Temperature
工作温度 |
10~+45℃ | Charge充电 | |
-10~+60℃ | Discharge放电 | |||
13 | Storage Temperature
储存温度 |
Less than 1 year: -20~+25℃
少于1年:-20~+25℃ |
Recommend to charge and discharge at least 1 time to maintain battery.
建议至少要对电池进行一次充放电,进行电池性能维护。 |
|
Less than 6 months: -20~+30℃
少于6个月:-20~+30℃ |
||||
Less than 3 months: -20~+40℃
少于3个月:-20~+40℃ |
||||
14 | Storage Humidity
储存湿度 |
65±20% RH | ||
15 | Weight
重量 |
Approx: TBD
大约: TBD |
||
16 | Product Dimensions
产品尺寸 |
Length: Max52.0mm/Min50.5mm
长度:Max52.0mm/Min50.5mm |
Initial battery dimensions
初始电池尺寸 |
|
Width: Max34.5mm/Min33.0mm
宽度:Max34.5mm/Min33.0mm |
||||
Thickness: Max5.4mm/Min4.9mm
厚度:Max5.4mm/Min4.9mm |
||||
17 | Open Voltage
出厂电压 |
3.8-3.95V |
Electric features
No. | 项目
Item |
单位
Unit |
最小值
Min. |
中间值Typ. | 最大值
Max. |
备注(Remark) |
1 | 过充保护电压
Over charge protection voltage |
V | 4.275 | 4.30 | 4.325 | 来源IC规范
Source of IC spec |
2 | 过充保护延时时间
Delay time for over charge protection |
s | 0.7 | 1.0 | 1.3 | 来源IC规范
Source of IC spec |
3 | 过充电解除电压
Over charge release voltage |
V | 4.03 | 4.08 | 4.13 | 来源IC规范
Source of IC spec |
4 | 过放电保护电压
Over discharge protection voltage |
V | 2.95 | 3.000 | 3.05 | 来源IC规范
Source of IC spec |
5 | 过放保护延时时间
Delay time for over discharge protection |
mS | 89.6 | 128 | 166.4 | 来源IC规范
Source of IC spec |
6 | 过放电解除电压
Over discharge release voltage |
V | 2.9 | 3.0 | 3.1 | 来源IC规范
Source of IC spec |
7 | 放电过流保护测试值
Discharge Over current protection testing values |
A | 1.1 | 1.6 | 3 | 来源IC\MOS规范
Source of IC \MOSspec |
8 | 放电过电流保护延迟时间
Delay time for discharge over current protection |
mS | 5.6 | 8 | 10.4 | 来源IC规范
Source of IC spec |
9 | 充电过流保护测试值
Charge Over current protection testing values |
A | 1.1 | / | 3 | I=VM/RSS(MOS内阻)
I=CS/RSS(电阻) |
10 | 充电过流保护延迟时间
Delay time for charge over current protection |
mS | 5.6 | 8 | 10.4 | 来源IC规范
Source of IC spec |
11 | 短路保护延迟时间
Delay time for short circuit protection |
uS | 200 | 280 | 400 | 来源IC规范
Source of IC spec |
12 | 保护电路的功耗 VDD=3.9V,VM=0V
Power consumption of protection circuit |
uA | / | 4.0 | 6.0 | 来源IC规范
Source of IC spec |
13 | PCM内阻(B-和P-间内阻B+和P+间没算在内)
PCM Internal Resistance |
mΩ | / | / | 65 | 元件+PCB内阻 |